Coast Guard Headquarters, 2100 Second Street SW., Washington, DC 20593-0001, between 9 a.m. You may inspect the material incorporated by reference at room 1312, U.S. You may also find this docket on the Internet at. and 5 p.m., Monday through Friday, except Federal holidays. Comments and material received from the public, as well as documents mentioned in this preamble as being available in the docket, will become part of this docket and will be available for inspection or copying at room PL-401 on the Plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. The Docket Management Facility maintains the public docket for this rulemaking. (4) Electronically through the Web Site for the Docket Management System at. (3) By fax to the Docket Management Facility at 20. (2) By delivery to room PL-401 on the Plaza level of the Nassif Building, 400 Seventh Street SW., Washington, DC, between 9 a.m. Department of Transportation, room PL-401, 400 Seventh Street SW., Washington, DC 20590-0001. (1) By mail to the Docket Management Facility (USCG-1999-5151), U.S. The incorporation by reference of publications in this rule was approved by the Director of the Federal Register on February 29, 2000.ĪDDRESSES: To make sure your comments and related material are not entered more than once in the docket, please submit them by only one of the following means: If you submit an adverse comment, or notice of intent to submit an adverse comment, the Coast Guard will withdraw this rule and publish a timely notice of withdrawal in the Federal Register. This rule incorporates the most recent editions of the standards to ensure the use by regulated industry of the latest technology.ĭATES: This direct final rule is effective on February 29, 2000, unless a written adverse comment, or written notice of intent to submit an adverse comment, reaches the Docket Management Facility on or before January 31, 2000. Some of the standards incorporated were over 30 years out of date. SUMMARY: By this direct final rule, the Coast Guard amends Titles 33 and 46, Code of Federal Regulations, to render current the standards incorporated by reference from the American Society for Testing and Materials (ASTM). Update of Standards From the American Society for Testing and Materials (ASTM) Reinforced concrete pipe shall conform to ASTM Standard Specifications for Reinforced Concrete Culvert, Storm Drain, and Sanitary Sewer Pipe, Designation C76.Īll materials shall conform to applicable provisions of the AISC Specifications for the design and fabrication of structural steel, and to pertinent ASTM Standard Specifications.From the Federal Register Online via GPO Access ģ3 CFR Parts 127, 154, 155, 159, 164, and 183 andĤ6 CFR Parts 28, 30, 32, 34, 35, 38, 39, 54, 56, 58, 61, 63, 76, 77, 78, 92, 95, 96, 97, 105, 108, 109, 110, 111, 114, 119, 125, 151, 153, 154, 160, 161, 162, 163, 164, 170, 174, 175, 182, 190, 193, 195, and 199 These holes shall be sealed with cement mortar using one part Portland Cement to two parts clean sand, meeting ASTM Standard Specifications, Serial Designation C144. PVC pipe and fittings less than 15 inches in diameter shall conform to the requirements of ASTM Standard Specifications for Type PSM Polyvinyl Chloride (PVC) Sewer Pipe and Fittings, Designation D 3034.īolts, anchor bolts, nuts and washers, specified to be galvanized, shall be zinc coated, after being threaded, by the hot-dip process in conformity with the ASTM Standard Specification for Zinc (Hot- Galvanized) Coatings on Products Fabricated from Rolled, Pressed and Forged Steel Shapes, Plates, Bars and Strip, Designation A123, or the ASTM Standard Specifications for Zinc Coating (Hot Dip) on Iron and Steel Hardware, Designation A153, as is appropriate. Material specifications, methods of sampling, and testing procedures shall conform to ASTM Standard Specifications. Precast concrete sections and appurtenances shall conform to the ASTM Standard Specifications for Precast Reinforced Concrete Manhole Sections, Designation C478, latest revision, with the following exceptions and additional requirements.Ĭastings shall be at least Class 25 conforming to the ASTM Standard Specifications for Gray Iron Casting, Designation A48, latest revision. New bricks shall conform to the requirements of ASTM Standard Specifications for Building Bricks Designation C902 SX for Grade SW.Īllowable ASTM Specifications: All material, manufacturing operations, testing, inspection, and making of HDPE pipe shall conform to the requirements of the appropriate allowable ASTM Standard Specifications, latest revision thereof, listed in Article References.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |